ASQ CQT Exam Questions With 100% Correct Answers 2023, Exams of Advanced Education

Download ASQ CQT Exam Questions With 100% Correct Answers 2023 and more Exams Advanced Education in PDF only on Docsity!

ASQ CQT Exam Questions With 100%

Correct Answers 2023

One advantage of 100% inspection over sampling inspection is that 100% inspection (A) provides more information about quality levels (B) gives zero defects to the customer (C) reduces the personal bias of the inspector (D) requires less machine-operator training - Correct Answer-A provides more information about quality levels When the term "R & R" is applied to digital calipers, it refers to (A) removal and replacement (B) relativity and reproducibility (C) repeatability and reliability (D) repeatability and reproducibility - Correct Answer-D repeatability and reproducibility The proper method of placing parts on a surface plate and then removing them is (A) rotate on and slide off (B) rotate on and lift off (C) set on and slide off (D) set on and lift off - Correct Answer-A rotate on and slide off Who is responsible for determining whether a follow-up response is sufficient to close out an internal audit? (A) Executive management (B) The quality manager (C) The audit team leader (D) The internal auditee - Correct Answer-C The audit team leader Which of the following methods is used to develop an exhaustive list of ideas about a subject? (A) Goal-setting (B) Brainstorming (C) Benchmarking (D) Problem-solving - Correct Answer-B Brainstorming A document that asserts that a product conforms to specification is known as a certificate of (A) qualification (B) validation (C) calibration

(D) compliance - Correct Answer-D compliance Confidence limits are generated in order to define the (A) limits of random variation around a control value (B) limits that contain all future observations (C) interval within which a population parameter lies (D) amount of variation that the process exhibits - Correct Answer-C interval within which a population parameter lies The purpose of a calibration schedule is to (A) detect deterioration of accuracy (B) meet ISO audit requirements (C) test inspector performance (D) increase product acceptance - Correct Answer-A detect deterioration of accuracy What is the percent yield for a normally distributed process in which the item length specification is 5.750 ± 0.004, X is 5.752, and the standard deviation is 0.002? (A) 15.73% (B) 19.15% (C) 47.72% (D) 83.99% - Correct Answer-D 83.99% In preparation for construction of a cause and effect diagram, it is important to (A) plot separate charts for each source (B) focus only on what makes things go wrong (C) record everything people suggest (D) validate possible root causes - Correct Answer-C record everything people suggest A quality technician uses a c chart to monitor the number of defects in a square foot of material. After the initial startup period, the mean number of defects is calculated at 13.5. What should the control limits be for the c chart? LCL UCL (A) 0.00 54. (B) 0.00 27. (C) 2.48 24. (D) 9.83 17.17 - Correct Answer-C 2.48 24.

The shape of the distribution above is best described as (A) normal (B) multi-modal (C) positively skewed (D) negatively skew - Correct Answer-C positively skewed A material review board (MRB) usually has the responsibility for which of the following? (A) Analyzing and dispositioning of nonconforming material (B) Defining the statistical specifications of nonconforming material (C) Assuring the availability of materials to meet production schedules (D) Controlling the cost of materials - Correct Answer-A Analyzing and dispositioning of nonconforming material The most common form of specification in manufacturing facilities is the (A) control plan (B) operator instruction sheet (C) blueprint (D) in-process check sheet - Correct Answer-C blueprint Statistical quality control generally requires inspection to be conducted (A) at the warehouse to maintain quality of parts in storage (B) immediately after the production run has been completed (C) close to the point of production of the part (D) when the product is received by the customer - Correct Answer-C close to the point of production of the part A process is running 1.5% defective. The sampling plan used for this process is n= 40; accept/reject = 2/3. What is the probability of rejecting a lot from this process? (A) 0. (B) 0. (C) 0. (D) 0.3328 - Correct Answer-A 0. Inspection accuracy increases with (A) reductions in defect rates (B) repeated inspections (C) additional product complexity (D) order of sample selection - Correct Answer-B repeated inspections

If a distribution is normal, with μ = 50 and σ = 15, what percentage of data will be less than 30? (A) 59.18% (B) 40.82% (C) 9.18% (D) 1.33% - Correct Answer-C 9.18% The primary purpose of a first-article inspection is to (A) teach the inspector how to check the part (B) gather information on process capability (C) verify that the sampling plan is appropriate (D) ensure that the part conforms to specifications - Correct Answer-D ensure that the part conforms to specifications The reduction or elimination of incoming inspection stations should be considered only when (A) evidence of supplier process control techniques is provided for the material used (B) evidence of a high defect rate is present in the manufacturing operation (C) the next process step will mask defects (D) it is cost-prohibitive to the supplier to test the parts - Correct Answer-A evidence of supplier process control techniques is provided for the material used A company is receiving an unusually high number of returns from various customers. The first step in investigating the problem would be to (A) check the inspection records (B) establish the correlation of the returns to shipments (C) brainstorm the potential causes (D) classify the returns by type and degree of seriousness - Correct Answer-D classify the returns by type and degree of seriousness A long-term corrective action plan is best described as a (A) remedial action already taken (B) temporary action on a current condition (C) permanent action on an underlying cause (D) containment action applied immediately - Correct Answer-C permanent action on an underlying cause Which of the following is the first step for a technician to take when a nonconforming product has been discovered? (A) Contact quality management. (B) Determine the product's fitness for use. (C) Quarantine the product.

(D) Rework the product. - Correct Answer-C Quarantine the product. The weakest step in the corrective action process is usually (A) finding the problem (B) containing the problem (C) developing an action plan (D) following up on the problem - Correct Answer-D following up on the problem When dial indicators are used, the most common cause of cosine error is the result of the (A) operator viewing the dial at an angle (B) operator not counting the number of revolutions the dial has made (C) indicator tip being at an angle to the surface being measured (D) indicator not being referenced to a calibrated surface - Correct Answer-C indicator tip being at an angle to the surface being measured The accuracy of a profilometer is verified with (A) fingernail comparators (B) surface plates (C) calibration patches (D) optical flats - Correct Answer-C calibration patches In a team meeting, the primary responsibility of the facilitator is to (A) record key topics (B) post ideas on a flipchart (C) keep the meeting focused (D) keep track of time - Correct Answer-C keep the meeting focused Which of the following is the best definition of a flow chart? (A) A diagram used to structure ideas into useful categories (B) An illustration used to analyze variation in a process (C) A picture used to separate steps of a process in sequential order (D) An analytical tool used to clarify opposing aspects of a desired change - Correct Answer-C A picture used to separate steps of a process in sequential order What is the standard deviation of the population below? 10, 4, 16, 12, 8 (A) 4. (B) 4.

(C) 16.

(D) 20.00 - Correct Answer-A 4. The ability of a material to resist mechanical penetration is a test of (A) surface finish (B) hardness (C) tensile strength (D) porosity - Correct Answer-B hardness Which of the following elements of an audit program must be aligned with the organization's overall strategy? (A) Objectives (B) Schedule (C) Scope (D) Compliance - Correct Answer-A Objectives Which of the following types of micrometers is best for detecting external out-of-roundness on a cylindrical part? (A) Blade (B) Three-point (C) V-anvil (D) Depth - Correct Answer-C V-anvil Tolerances are specified for machined parts for which of the following reasons? (A) The process used to produce the parts needs improvement. (B) The machines used to produce the parts have inherent variation. (C) The tolerances establish productivity measures. (D) The tolerances identify areas of improvement for the machines. - Correct Answer-B The machines used to produce the parts have inherent variation. The extent to which an instrument replicates its result when measurements are taken repeatedly on the same unit is called (A) real bias (B) precision (C) accuracy (D) true value - Correct Answer-B precision In a normal distribution, what percentage of data falls within ± 3σ of the mean? (A) 95.46% (B) 99.73% (C) 99.96%

(D) 100.00% - Correct Answer-B 99.73% Which of the following tools would be best for measuring projected surface intersections? (A) Optical comparator (B) Thread micrometer (C) Profilometer (D) Protractor - Correct Answer-A Optical comparator The check standards used in performing gage calibrations must be (A) traceable to national standards (B) used in a controlled environment (C) labeled to reflect their tolerance (D) applied with tamper-proof seals - Correct Answer-A Which of the following groups is responsible for producing parts to specifications? (A) The manufacturing engineering department (B) The process engineering department (C) The manufacturing department (D) The quality assurance department - Correct Answer-C The manufacturing department When applied to size features such as hole and shaft diameters, MMC refers to (A) maximum shaft diameter, maximum hole diameter (B) minimum shaft diameter, minimum hole diameter (C) maximum shaft diameter, minimum hole diameter (D) minimum shaft diameter, maximum hole diameter - Correct Answer-C maximum shaft diameter, minimum hole diameter SAMPLES 1 2 3 4 5 6 7 3 2 1 −1 3 2 3 1 3 3 −1 2 1 2 −1 0 2 2 −1 1 1 2 −2 1 1 2 −1 3 −1 4 1 0 2 0 3 On the basis of the control chart sample above, what is the upper control limit (UCL) for the average? (A) 1. (B) 3. (C) 3. (D) 7.25 - Correct Answer-B 3. Which of the following measures is a sufficient statistic

for the parameter μ? (A) Median (B) Mid-range (C) Mean (D) Mode - Correct Answer-C Mean A process audit is best described as (A) a detailed examination of a finished product (B) an examination of an activity to verify conformance to established procedures (C) an examination of the management methods used in a company (D) an independent evaluation of various aspects of part performance - Correct Answer-B an examination of an activity to verify conformance to established procedures If a multi-range instrument is found to be inaccurate on one range, the instrument may be used only if (A) it is approved by the customer for all ranges (B) it is prominently labeled to indicate its use restrictions (C) quality assurance personnel supervise its use (D) detailed training is given on its limited use - Correct Answer-B it is prominently labeled to indicate its use restrictions What is the recommended minimum number of subgroups necessary to calculate the limits for a control chart? (A) 10 (B) 15 (C) 25 (D) 35 - Correct Answer-C 25