CM 2215 OSHA 510 Study Guide with Complete Solutions, Exams of Workplace Safety

Download CM 2215 OSHA 510 Study Guide with Complete Solutions and more Exams Workplace Safety in PDF only on Docsity!

CM 2215 OSHA 510 Study Guide with

Complete Solutions

Protect safety and health of America's workers - ANSWER-OSHA's mission is to 11(c) - ANSWER-The right of the worker to seek safety and health on the job site without fear of punishment can be found in Section___ of the OSH Act lower morale and increased training costs - ANSWER-Results of workplace injuries and illnesses may include specific industry - ANSWER-Horizontal standards apply when a condition is not covered by a ___ ___ standard consistent - ANSWER-The purpose of OSHA directives, including Enforcement and Compliance Directives (CPL), is to ensure ___ OSHA regulations cited violation - ANSWER-OSHA requires that employers certify that abatement is complete for each ___ its workers - ANSWER-Creating employer failed to inform employees, other than ___, of damaged guardrail would result in a "creating" employer receiving a citation under OSHA's multi-employer citation policy for damaging a guardrail exposing all employees to a fall hazard. opening, walk through/around, closing - ANSWER-In addition to the presentation of credentials, the inspection process includes the ___ conference, the ___ inspection, and the ___ conference. partial - ANSWER-As a result of a work-related illness or injury, days the employee was only able to work a ___ shift would be classified as restricted work activity (not including the day the illness or injury began). 100 - ANSWER-In OSHA Record keeping, an incidence rate is the number of recordable injuries or illness per ___ full-time workers. following - ANSWER-Managers should be an example by knowing and ___ the rules employees are expected to follow to demonstrate management leadership and commitment to safety and health competent - ANSWER-The two main components of an employer's accident and prevention responsibilities required by 1926.20(b) a safety and health program and jobsite inspections by a ___ person.

100 - ANSWER-The maximum travel distance from any point of the protected area to the nearest fire extinguisher shall not exceed ___ feet visible - ANSWER-Accident prevention signs such as; danger, caution, and exit signs shall be ___ when work is being performed. 3.5 - ANSWER-When stopping a fall, a personal fall arrest system, shall bring an employee to a complete stop and limit the maximum deceleration distance to ___ feet. maintained - ANSWER-All hand and power tools, whether paid for by the employer or employee, shall be ___ in a safe condition. qualified - ANSWER-A person who has a recognized degree, certificate, or professional standing or who has demonstrated his/her ability to solve problems relating to specific work is a ___ person. sheilded - ANSWER-Whenever practicable, all arc welding and cutting operations shall be ___ to protect employees and other persons working in the vicinity fire - ANSWER-Failure to inspect for oil or grease on regulator fittings, valves, or the cap threads on a cylinder of oxygen can result in ___ or explosion. 6 - ANSWER-Personal fall arrest systems, when stopping a fall, shall be rigged such that an employee cannot free fall more than ___ feet or contact any lower level. 10 - ANSWER-When mechanical equipment is being used perpendicular to the roof edge, the warning lines cannot be closer than ___ feet. employer's - ANSWER-It is the ___ responsibility to initiate and maintain accident prevention programs to comply with all applicable standards permanent - ANSWER-An "Assured equipment grounding program" deals with the cord- set and receptacles which are not part of the ___ wiring of the building or structure. 50 - ANSWER-___ volts or greater is the maximum voltage before guarding is required against accidental contact by cabinets, other forms of enclosure, or by location in a room or enclosure accessible only to qualified persons (electricians). bonding - ANSWER-The practice of connecting two metallic objects to prevent static sparks is called ___ inspection, test - ANSWER-Before the start of any work covered under Subpart V - Power Transmission and Distribution, existing conditions are determined by an ___ or a ___.

competent - ANSWER-OSHA requires that scaffolding being erected, moved, dismantled or altered be supervised by a ___ person. 42 - ANSWER-According to 1926.502(b)(1), the top rail of a guardrail system must be a height of ___ inches +/- 3 inches above the walking/working level. 45 - ANSWER-A material chute used during demolition operations bust be enclosed when its angle is equal to or greater than ___ degrees above the horizontal. B - ANSWER-Sandy clay loam having unconfined compressive strength of 1.2 TSF is a Type ___ soil. 8 - ANSWER-___ ft is the trigger height when masonry walls must be braced. 3 - ANSWER-On temporary stairs, handrails (to provide adequate handholds for employees grasping to prevent falling) shall have a minimum clearance of ___ inches between the handrails and walls 4 - ANSWER-When masonry walls are being constructed, a limited access zone at least the height of the wall plus ___ feet tall shall be established on the side of the wall without scaffolding. 4 - ANSWER-Except for extra-heavy-duty metal or plastic portable ladders, all portable ladders must support ___ times the maximum intended load. 30 - ANSWER-A controlled decking zone can only be used as fall protection up to a maximum height of ___ feet 12 - ANSWER-Type A soil can be sloped at 1/2:1 ratio if the excavation is open for less than 24 hours and is less than ___ feet deep. service - ANSWER-Portable ladders with structural defects such as, broken or missing rungs or split rails shall be removed from ___ until repaired 20 and 30, 48 - ANSWER-Cross bracing on a scaffold is only acceptable as a mid-rail when the crossing point of the two braces is between ___ and ___ inches above the work platform and end points are less than ___ inches apart. shift - ANSWER-Rigging equipment for material handling shall be inspected prior to use on each ___ and as necessary during use. operators - ANSWER-Crane ___ must have the authority to stop and refuse to handle crane loads until a qualified person has determined that safety has been assured.

stop - ANSWER-During crane operations when signalling is required, if the signals are interrupted the crane operator should safely ___ operations requiring signals until they are reestablished employer - ANSWER-The ___ is responsible to train signal persons to meet the 1926.1428 standard. 0 - ANSWER-The material used in rollover protection structures must have the capability of performing at ___ degrees F 178 - ANSWER-The operator training requirements for rough terrain trucks used in the construction industry are covered under OSHA standard 1910.___ Powered Industrial Trucks Z87.1 - ANSWER-Eye and face protection equipment used to protect against hazards shall meet the requirements specified in ANSI ___ Engineering, Administrative, Personal Protective Equipment - ANSWER-The correct hierarchy for controlling exposure to chemical hazards in 1. ___ controls, 2. ___ controls, 3. ___ ___ ___ 134 - ANSWER-Respirators used in the construction industry are covered under OSHA standard 1910.___ first aid - ANSWER-In the absence of an infirmary, clinic, hospital, or doctor that is reasonably accessible in terms of time and distance from the worksite, the employer shall make sure a person with a valid certificate in ___ training is available at the worksite. tap - ANSWER-According to OSHA, portable containers to provide drinking water shall be tightly closed and equipped with a ___ Lead - ANSWER-___ contaminants are toxic to both male and female reproductive systems and can create significant exposure to workers removing paint from bridges, renovating residences, and demolishing or salvaging structures