MSSC Safety study questions with correct answers, Exams of Workplace Safety

Download MSSC Safety study questions with correct answers and more Exams Workplace Safety in PDF only on Docsity!

MSSC Safety study

The first step to a job safety analysis is to:Document an itemized sequence of job tasks. What does NIOSH stand for?National Institute for Occupational Safety and Health An employee questions the quality of the materials inside a trailer and pages his/her supervisor to come to the trailer. It is clear that the contents have been seriously damaged in the shipment. which of the following actions is appropriate?Reject the load to the carrier Several Federal agencies enforce regulations concerning the workplace. The federal agency concerned with enforcement of the safety regulations is :OSHA Which of the following is not a requirement of a fixed ladder ?The distance between the rungs shall exceed 16" Audits of environmental or quality system within an organization typically include all of the following EXCEPT :Detailed instructions on how to improve the system A job safety analysis should NOT be conducted by?An OSHA representative The risk of injury for new employees is _______________ than for those with experience.More likely In most manufacturing plants , the chance of being exposed to the blood-borne pathogens is relatively small. In these plants, the Greatest risk of exposure is :Contact with bodily fluids while administering first aid To make sure the receiver has understood a message, you should:Have the recipient rephrase what was said in his/her own words

The primary need for training in today's manufacturing environment is :Change in people/processes What color code is commonly used to on MSDS indicate areas where radiation is present?Black on yellow Noise induced hearing loss first affects the ability to hear:High frequency sounds What term is used to express the airborne concentration of material to which most persons can be exposed to day after day without adverse effectsThreshold limit value In addition to a welding helmet and welding gloves , other Personal Protective Equipment (PPE) is commonly used during welding?Leather apron Manufacturing use _________ to reduce air pollution and meet government standards for environmental protectionCleaner energy sources and Energy-efficient machines What does the abbreviation "MSDS" stand for?Material Safety Data Sheet Flammable liquids are different from combustible liquids in that:Flammable liquids have flashpoints below 100 F and combustible liquids have flashpoints above 100 F Tool and equipment safety are designed to protect workers from workplace hazards. Most these safety system are regulated and enforced by the:OSHA The clean Air Act requires that a risk assessment be completed. Which of the following is the LEAST important reason for doing the risk assessment ?To evaluate the potential for fines and lawsuits It is important that the workplace be safe and efficient. The science of designing and arranging things people use is called:Ergonomics OSHA requires reporting of incidents that hospitalized at least thee workers or kill one or more workers:Within 8 hours

The Hazardous Material Identification System rates health, flammability, and physical hazard categories. On such a scale, a high level of danger is indicated by:The Number 4 Job training can involve many different aspects of a particular job. However, training should always cover information about:Safety Members of a safety committee generally include both front line workers and managers. One of the primary duties of the safety committee is :Responding to worker safety concerns. What does PPE stand for?Personal Protection Equipment What should be checked before draining a dike area of rainwater?Presence of visibility sheen of oil on the surface of water Safety hazards and concerns should be reported to a safety committee member or a manager. If no action is taken by the company to improve the problem, the employee should:File a complaint with OSHA Which of the following external parties would be used to insure compliance with safety guards?Third party safety consultants Which of the following is NOT a device that is designed to prevent an operator from entering an unsafe work area?Sign-in log When a hazardous situation is discovered during an inspection , action must be taken. The best solution is to:Eliminate the hazard by changing the process Workers involved in shipping hazardous products must be familiar with Department of Transportation (DOT) regulations. These regulations cover:Packaging , Incident reporting , Training A good way to initiate an action plan is to:Brainstorm ideas

Gas fires are considered to be type _____ fires.B Which of the below are three examples of engineering controls?Ventilation systems, machines guards, and circuit breakers. The person who preforms the next step in a production process is considered to be a/an ____ to the person who preformed the previous step.Internal Customer The purpose of the third wire on a safety designed 100vt power tool is to:Provide proper grounding of the tool The eight hour hazmat refresher training is requiredAnnually What is the distance that the floor should be kept free of combustible material when welding or cutting? 35 feet A forklift should always be driven the reverse gear when:The load obscures the view forward What is a/an acceptable, safe number of air hoses that can cross a walkway?Zero The operator should wear a/an_____ when using a grinderFace shield and safety glasses A worker needs to lift 5,500 pounds, but the hoist rating is 5,000 pounds. What should the worker do? Secure a hoist with a larger rating To check for leaks on a half mask respirator when inhaling, a worker should cover the ____ with the palms of his handCartridges The United Nations number for a hazardous material is used for identifying?The material being shipped

Transportation of hazardous materials is regulated by?Department Of Transportation The proper storage of inspection recorded is determined byCompany policy Fire drill documentation should include the date, time of the drill, the evacuation time, andA description of any problems observed After a new production employee has been through the safety orientationHis or her participation is documented according to company policy Recognizing and reporting improperly guarded equipment is the responsibility ofEveryone What will prompt an OSHA inspection ?Report of imminent danger, Employee complaint, Referral A OSHA Safety citation should be posted for _______ daysThree days or until abated whichever is longer What is NOT a long term, or chronic , effect of overexposure to chemicals?Sudden Spontaneous combustion A guardrail must be ________ high42 inches Portable fire extinguisher maintenance includes checking to ensure thatThe extinguisher is fully charged, Is in its designated place, It is accessible The Proper device to clean a file is a:File Card Written procedures of lockout / tagout (LOTO) areRequired What risk factors determine if repetition contributed to an MSD?Repeated motion, Required force , Speed of movement

The most common bloodborne pathogen (BBP) found in the workplace isHepatitis B Virus (HBV) What bodily fluid may contain BBP's?Urine, Saliva , Vomit