OSHA Final Exam 2024 Questions and Answers 100% Verified, Exams of Workplace Safety

Download OSHA Final Exam 2024 Questions and Answers 100% Verified and more Exams Workplace Safety in PDF only on Docsity! OSHA Final Exam 2024 Questions and Answers 100% Verified OSHA's mission is to - ANSWER-Protect the safety and health of america's workers The creation of OSHA provided this important right to workers - ANSWER-the right to a safe and healthful workplace The OSHA standards for contruction and general industry are also known as: - ANSWER-Part 1926 and part 1910 if you feel that an OSHA inspection is needed to get hazards corrected at your workplace, which is your best option? - ANSWER-submit a written, signed complaint with specific hazard information The right of workers to seek safety and health on the job without fear of punishment is spelled out in - ANSWER-section 11(c) of the OSH act MSDS sheets give info about - ANSWER-hazardous chemicals Osha requires that employers pay for most required PPE including: - ANSWER-Hard Hats one of the ain responsibilities employers have under OSHA is to: - ANSWER-provide training required by OSHA standards What type of OSHA inspection is conducted when immediate death or serious harm is likely? - ANSWER-imminent danger when the emplyer receives an OSHA citation, it must be - ANSWER-posted for 3 days or until the violation is fixed during an osha inspection - ANSWER-you have the right t talk to the inspector privately among the rights related to osha recordkeeping, workers have the right to review - ANSWER-the osha 300 log and teh OSHA 300A summary The abatement date is the date to - ANSWER-correct violation within 10 calendar days after _______, the employer must certify to OSHS that each cited violation has been abated - ANSWER-abatement date advance notice of inspection is always given to the employer - ANSWER-false each citation (one or more copies) should be posted for employees until a violation is abated for _________ working days - ANSWER-3 if the employer objects to the inspection, the Safety and Health officer will - ANSWER- terminate the inspection or continue the inspection in area where no objection is raised the employer must post a copy of each docment submitted to the agency or a summary of the document - ANSWER-in a place near where the violation occurred the employer must comply with an employee's or employee representative's request to examine and copy abatement documents within_______ working days of receiving the request - ANSWER-5 in cases of apparent imminent danger, advance notice of inspection - ANSWER-will be given which of the following will be given an opportunity to accompany the compliance safety and health officer during the physical inspection of any workplace for the purpose of aiding such inspection? - ANSWER-all of the above it is not necessary to implement safety and health programs in the workplace to reduce the likelihood of employee injury and added costs - ANSWER-false which of the folowing can be a result of not implementing a safety and health program into the workplace? - ANSWER-all of the above education and training in safety and health protection is especially critical for employees who are assuming new duties - ANSWER-true __________focuses on the relationship between the worker, the task, the tools and the work environment - ANSWER-job hazard analysis a question such as- is one person clearly responsible for the overall activities of the safety and health program?- should be part of the : - ANSWER-safety and health checklist if an employee receives a severe injury and loses his fingers and hands, this is an example of - ANSWER-the consequences of the hazard which of the following is implemented during a worksite analysis - ANSWER-all of the above all exit route environments should be well lit so that an employee along the route - ANSWER-false contents which are liable to burn extremely fast or that can produce poisonous fumes or explosions in a fire are known as - ANSWER-high hazard contents which of the following persons is resonsible for fire detection systems being designed to operate in time to control or extinguish a fire? - ANSWER-both a and b in order to be fully operational, fire detectors need to be cleaned of - ANSWER-all of the abov the employer must post hazard warning or caution signs at the entrance to, and inside of, areas protected by fixed extinguishing systems which use agents in concentrations known to be hazardous to employee safety and health - ANSWER-true generally, it is important that the employer not delay alarms or devices initiated by fire detector actuation for more than: - ANSWER-30 seconds all standpipe systems installed before Jan. 1, 1981, for use by employees, must be equipped with the lined hose - ANSWER-false the employer must restore all fire detection systems and components to normal operating condidtion as promptly as possible________ each test or alarm - ANSWER- after Any defects or impairments of fixed extinguishing systems must be properly corrected by the employee - ANSWER-false all fire detection systems must be tested and adjusted_______ to maintain proper reliability and operating condition except that factory calibrated detectors need not be adjusted after installation - ANSWER-as often as needed hose systems must be inspected at least _________and after each use to assure that all of the equipment and hos are in place, available for use and in serviceable condition - ANSWER-annually the employer must ensure the use of ________needed for immediate rescue of employees trapped in hazardous atmospheres created by an agent discharge - ANSWER-PPE which of the following is not approved or suitable for use with flexible cords and cables? - ANSWER-none of the above if you come into contact with an energized black wire and you are also in contact with a white grounded wire - ANSWER-current will pass through you body and you will receive a shock in general, a disconnecting means must be located in sight from the controller location - ANSWER-true in general, a disconnecting means must be located in sight from the controller location - ANSWER-true overcurrent devices for circuits rated 600 volts nominal or less must be reaily accessible to each employee or authorized building management personnel - ANSWER-true all circuits breakers must clearly indicate whether they are in the open ___ or closed- ____ position - ANSWER-off,on workers in elevated locations who experience a shock can fall, resulting in serious injury or death - ANSWER-true an open conductor must have at least 18 feet of clearance above a public street - ANSWER-true dry skin has a fairly high resistance, but when moist, resistance drops radically, making it a ready conductor - ANSWER-true if metal covers are used for __________, they must be grounded - ANSWER-all of the above temporary wiring over 600 volts, nominal, may be used only during - ANSWER-all of the above non-power-limited fire protective signaling circuits and ______ cuircuits may occupy the same enclosure, cable, or raceway provided all conductors are insulated for maximum voltage of any conductor within the enclosure, cable or raceway - ANSWER-class 1 emergency circuit wiring must be kept entirely independent of all other wiring equipment - ANSWER-true if too many devices are plugged into a circuit, the current will heat the wires to a very high temperature which may cause a fire, this is known as a(n) - ANSWER-overload hazard _________labels must be attached on the equipment and be plainly visible even when doors are open or panels are removed from compartments containing voltages of over 250 volts AC or DC - ANSWER-danger AC systems supplying fixed and portable electric equipment within the cell line working zone need not be grounded - ANSWER-true qualified persons must, at a minimum, be trained in and familiar with the following - ANSWER-all of the above if work is to be performed near overhead lines, the lines must be __________or other protective measures must be provided before work is started - ANSWER-both a and c according to safe work practices for deenergizing equipment, each tag must contain a statement: - ANSWER-prohibiting unauthorized operation of the disconnecting means and removal of the tag conductors emerging from the ground must be enclosed in approved raceways - ANSWER-true a limit switch or other device must be provided to prevent the load block from passing the safe upper limit of travel of any hoisting mechanism - ANSWER-true The third step to controlling a hazard when handling spills or leaks is - ANSWER- contain the material the ____ the flash point, the _____the hazard - ANSWER-lower, greater when vapors of a flammable or combustible liquid are mixed with air in the proper proportions in the presence of a source of ignition, rapid combustion or an explosion can occur - ANSWER-true which of the following is prohibited to use for storage of a flammable or combustible liquid? - ANSWER-open metal container inside a storage cabinent portable fire extinguishment and control equipment must be provided - ANSWER-in such quantities and types as are needed for the special hazards of operation and storage transferring flammable liquids by mean of air pressure on the container or portable tanks is acceptable - ANSWER-false materials which react with water must not be stored in the same room with flammable or combustible liquids - ANSWER-true storage cabinets must be designed and constructed to limit the internal temperature to not more than 325F when subjected to a standardized 10-minute fire test - ANSWER- true defective ladders must be withdrawn from use and marked - ANSWER-dangerous, do not use some of the most frequently violated standards in regards to walking and working surfaces involve - ANSWER-housekeeping a standard railing must consist of - ANSWER-all of the above in circumstances for which it is impossible to provide such ventilation, airline respirators or hose masks approved for this purpose by OSHA must be used - ANSWER-false ventilation requirements are established on the basis of which of the following in arc and gas welding which govern the amount of contamination to which welders may be exposed - ANSWER-all of the above cables with splices within 10 feet of the holder may not be used - ANSWER-true the _______ is responsible for determining if combustible materials and hazardous area are present or likely to be present in the work location - ANSWER-supervisor which of teh following can cause hazards in welding, cutting, or heating - ANSWER-all of the above all doors and access panels of all resistance welding machines and control panels must be ________to prevent access, by unauthorized persons, to live portions of the equipment - ANSWER-a and c which of the following must helmets and hand shields be arranged to protect from contact with direct radiant energy - ANSWER-all of the above common side effects of exposure to high concentrations of cadmium fumes include - ANSWER-lung irritation empty cylinders must have their valves - ANSWER-closed a fire watch must be maintained for at least ______ after completion of welding or cutting operations to detect and extinguish possible smoldering fires - ANSWER-30 minutes all aisles and passageways must be ______ and permanent aisles and passageways must be permanently marked - ANSWER-kept clear, permanently marked employers must conduct an evaluation of each powered industrial truck operators performance at least once every____ years - ANSWER-3 when using slings it is advised to engage in shock loading - ANSWER-false training programs on proper lifting techniques should cover several topics including - ANSWER-all of the above trucks approved for fire safety also must bear a label, or some other identifying mark, indicating - ANSWER-it is accepted by a nationally recognized testing laboratory ___________focuses on the work environment, such as its design and function, as well as items such as the design and function of work stations - ANSWER-ergonomics employers and employees must equip fork trucks with vertical load backrest extensions according to ___________ specifications if the load presents a hazard - ANSWER-the manufacturer's the rated capacity of mobile cranes is the same regardless of the length of the boom and the boom radius - ANSWER-false the employer must provide a program to train all employees who service rim wheels in the hazards involved in servicing those rim wheels and the safety procedures to be followed - ANSWER-true some powered industrial trucks are intended for use in atmospheres which may be flammable and are equipped with safeguards to their: - ANSWER-all of the above even if there are no guidelines specific to the industry, an employer still has an obligation under_________ to keep the workplace free from recognized serious hazards, including ergonomic hazards - ANSWER-general duty clause, section 5(a)(1) to avoidlifting injuries, you can use _______ to load machinery into trucks rather than lifting it - ANSWER-a and b good ergonomic work practice includes continually identifying the most hazardous tasks and implementing ________ and________ controls to help reduce or prevent injuries in those tasks - ANSWER-engineering, work practices ________ temperatures can cause decreased muscle flexibility, which can result in muscle pulls - ANSWER-cold osha does not issue citation for ergonomic related hazards - ANSWER-false regardless of how good your working posture is, working in the same position or sitting still for prolonged periods is not healthy - ANSWER-True the three steps to approaching ergonomic problems in the workplace are - ANSWER- review injury and illness records, identify potential MSD cases categorize devices used to laterally transfer a patient/resident, for example from bed to gurney are known as - ANSWER-lateral trnsfer devices maintaining sttic postures, such as viewing the monitor, for prolonged period of time without taking a break can fatigue the muscles of the _____and______ that support the head - ANSWER-neck, shoulders if metal covers are used for __________, they must be grounded - ANSWER-all of the above the terms "permit-required confined space and permit space" refer to spaces that meet osha's definition of a confined space and contain health or safety hazards - ANSWER- true which of the following is not a requirement to be included in the the written program for the permit space - ANSWER-none of the above control of atmoshpheric hazards through forced air ventilation constitutes elimination of hazards - ANSWER-false according to the entry chart, what must occur next if the space can not be maintained in a condition safe to enter by continuous forced air ventilation only? - ANSWER-prepare for entry via permit procedures which of the following is not a requirement to be included in the written program for the permit space - ANSWER-test atmospheric conditions in the permit space during and after space entry ________ the initial work assignment begins, the employer must provide proper training for all workers who are required to work in permit spaces - ANSWER-before one of the most dangerous situations associated with confined space entry is the failure to recognize a hazard exists - ANSWER-true employers must provide rescue service personnel with: - ANSWER-all of the above upon permit confined space entry, employers are required to provide at least one attendant outside the permit space into which entry is authorized for - ANSWER-the length of time the operations are to take place when testing for atmospheris hazards, employers are required to test first for oxygen, then for combustible gases and vapors and then for toxic gases and vapors - ANSWER- true