NCCER Test Practice Exam 2024-2025: Electrical Systems, Exams of Workplace Safety

Practice questions and answers for the nccer (national center for construction education and research) test, focusing on electrical systems. It covers topics such as guardrail systems, electrical circuits, grounding electrodes, overload sensing units, capacitance, wire cross-sectional area, drawing scales, heating cables, nema starters, neutral bus bonding, peak voltage, conductor jackets, sectional drawings, electrical safety, and revision blocks. Useful for students preparing for the nccer exam in electrical systems.

Typology: Exams

2024/2025

Available from 04/13/2025

Prof.Michael.Latest2025-2026Exams
Prof.Michael.Latest2025-2026Exams 🇺🇸

5

(2)

7.5K documents

1 / 4

Toggle sidebar

This page cannot be seen from the preview

Don't miss anything!

bg1
NCCER Test Practice Exam 2024-2025
Questions and Correct Answers
In a guardrail system, the guardrails can be made of any of the
following EXCEPT: a) pipe
b) chain
c) ropebanding
d) cable - ANSWER>>Ropebanding
If the potential across the circuit is 48 volts and the current is 5
amps the resistance of the circuit is: a) 4.8 ohms
b) 9.6 ohms
c) 48.0 ohms
d) 96.0 ohms - ANSWER>>9..6 ohms
A UL listed rod type grounding electrode must have a MINIMUM
length of: a) 6'
b) 8'
c) 10'
d) 20' - ANSWER>>8'
What is the MINIMUM number of overload sensing units required
for all three phase motors? a) 0
b) 1
c) 2
d) 3 - ANSWER>>3
In a circuit of pure capacitance, the current leads the voltage by
an angle of:
a) 30-degrees
pf3
pf4

Partial preview of the text

Download NCCER Test Practice Exam 2024-2025: Electrical Systems and more Exams Workplace Safety in PDF only on Docsity!

NCCER Test Practice Exam 2024- 2025

Questions and Correct Answers

In a guardrail system, the guardrails can be made of any of the following EXCEPT: a) pipe b) chain c) ropebanding d) cable - ANSWER>>Ropebanding If the potential across the circuit is 48 volts and the current is 5 amps the resistance of the circuit is: a) 4.8 ohms b) 9.6 ohms c) 48.0 ohms d) 96.0 ohms - ANSWER>>9..6 ohms A UL listed rod type grounding electrode must have a MINIMUM length of: a) 6' b) 8' c) 10' d) 20' - ANSWER>>8' What is the MINIMUM number of overload sensing units required for all three phase motors? a) 0 b) 1 c) 2 d) 3 - ANSWER>> In a circuit of pure capacitance, the current leads the voltage by an angle of: a) 30 - degrees

b) 45 - degrees c) 90 - degrees d) 180 - degrees - ANSWER>>90-degrees The standard unit for measuring the cross-sectional area of wire is the: a) circular mil b) square mil c) round mil d) radial mil - ANSWER>>Circular mil The drawing scale is MOST likely to be found in which of the following drawing locations? a) The lighting fixture schedule b) The symbol list c) The drawing title block d) The power riser diagram - ANSWER>>The drawing title block The length of bare copper conductor in a ground ring MUST be buried no less than 2.5' below grade and with a length of at least: a) 10 ft b) 20 ft c) 25 ft d) 50 ft - ANSWER>>20 ft When installing heating cables for anti-icing systems, cable pattern should be in a: a) criss-cross b) vertical zig-zag c) circular

d) side view of a building - ANSWER>>Cutaway view of a building Who is allowed to remove another electrician's tag or lock from any valve, switch, or piece of equipment without proper authorization? a) an inspector b) no one c) any supervisor d) owner - ANSWER>>No one The MAIN purpose of a revision block on an electrical drawing is to: a) Note any changes to the original drawings b) identify the professional engineer c) indicate the location of the project d) provide a title for the drawing - ANSWER>>Note any changes to the original drawings Which of the following is the classified location where combustible vapors are always present? a) Class I Div I b) Class II, Div II c) Class II, Div I d) Class III, Div I - ANSWER>>Class I Div I