Download STSC EXAM 2026 COMPREHENSIVE STUDY GUIDE COMPLETE SOLUTIONS and more Exams Nursing in PDF only on Docsity!
STSC EXAM 2026 COMPREHENSIVE STUDY
GUIDE COMPLETE SOLUTIONS
โ which is the first choice of protecting yourself if an armed suspect enters upur building? Answer: Run โ When being made aware of professional misconduct by a BCSP certification, what should you do? Answer: bring the misconduct to the BCSP and notify them โ which entity should complete the annual inspections of wite-strand rope? Answer: qualified person โ Which type of working platform is built using rigid, load-bearing members, such as poles, legs, frames, and outriggers? Answer: Supported โ When designing a fall arrest system, the use of locking carabiners and snap hooks that require two separate forces to be opened can greatly reduce the potential for which hazard? Answer: Roll out โ Which is the correct mechanical or electrical system used to prevent the operation of Hazardous machine functions under specified conditions? Answer: Interlocking Device interlock
โ When compressed air is used on-site for cleaning, which is the MAXIMUM pressure pound per square inch (psi) that is allowed? Answer: 30 psi โ Which method is used to reduce the risk of struck-by injuries caused by powered industrial trucks? Answer: Creating more space around corners and intersections for turning. โ A worker is exhibiting irritability, restlessness, red face, hot dry skin, shivering, disorientation, and body temperature greater than 104F. Which disorder is this and how would you apply first aid? Answer: Heat Stroke - quick effective cooling, take body temperature, and transport to hospital โ Which is the MOST effective way to prevent a backing incident when operating a commercial motor vehicle? Answer: Avoid backing up when not necessary. โ A worker recently brought a safety hazard to the attention of their supervisor. The supervisor conducted a job risk assessment and determined that there were several hazards associated with the workers job that had a potential to cause injury. What is this an example of? Answer: Recognizing and controlling hazards
โ Which is a good safety recommendation to make when using a wheelbarrow on a job site? Answer: Load as much material as can be safely handled when operating down a hill. โ Which is a BEST practice to reduce the risk of slips and trips? Answer: Good housekeeping โ According to BCSP code of ethics, when should public statements be made? Answer: Only when provided in an objective and truthful manner โ Which condition causes damage to tissue due to excessive exposure to low temperatures? Answer: Frostbite โ According to the Globally Harmonized System of Classification and Labeling of Chemicals, which are designated "signal words"? Answer: Warning and Danger โ If people in authority want others to follow their example, what should they do? Answer: Model the behavior they expect โ Fore extinguishers come with bumber tatings to indicate How large of a fire can be contained? For example, class a extinguishers may have a numeric rating of one, which indicates one gallon of extinguishing material. Which do number ratings for a class b or c indicate? Answer: The amount of square footage the unit will cover.
โ According to BCSP Code of Ethics, how and when should certificates provide public statements? Answer: Only in an objective and truthful manner and only founded upon the knowledge of the facts and competence in the subject matter. โ Which hand tool would be considered the safest to use? Answer: A power-driven screwdriver โ Which is the BEST definition of sloping in the context of excavation? Answer: Removing soil to cause a slant into the excavation. โ Which axe type should be used for hardwood? Answer: Narrow with thin blade. โ Which are the three sides of a fire triangle? Answer: Heat, Oxygen, Fuel โ Which is the easiest way to safeguard an operator using an electrical tool? Answer: Ground the tool โ What best describes common electrical workplace fire sources? Answer: Misuse of cords, sparking, short circuits
โ According to BCSP code of ethics, which action is taken if any professional misconduct is witnessed? Answer: Take steps to bring the misconduct to the attention of the BCSP. โ How many required sections are present on a safety data sheet? Answer: 16 โ Which group/function should be included on the team conducting site construction audits? Answer: Employee Representatives โ Which control prevents workers operating a machine or equipment from accessing the danger zone? Answer: Guard โ Which protective measures grouping provides the BEST protection to workers required to work or pass underneath the scaffolding? Answer: Guardrails, ยฝ" wire mesh, toe boards. โ Which is an example of a standard in the BCSP Code of Ethics that certificants should uphold? Answer: Seek opportunities to be of constructive service in civic affairs and work for the advancement of the safety, health, and well-being of their community and their profession by sharing their knowledge and skills. โ After an incident has occurred, which is the PRIMARY purpose for the investigation? Answer: to prevent recurrence of the incident.
โ A behavior-based safety observation should be based on what? Answer: Employee behavior โ If an employee wears splash goggles, a face shield, or full-face respirator, which hazard are they more likely protected from? Answer: Chemical liquids โ Which is the definition of deceleration distance? Answer: Distance from the fall arrest equipment to a complete stop. โ Which BEST describes a job hazard analysis as the process for examining a job? Answer: To determine how a task can ve accomplished safely โ Which common value or ethical code of conduct is known among EHS professionals? Answer: Protection of people, property, and the environment. โ Which are the four basic elements of a temporary traffic control zone? Answer: Advanced warning, taper, activity area, downstream. โ Which mistake do many organizations make in relation to their incident reporting programs? Answer: Requiring notifications of serious injuries only.
โ Which is an example of an administrative control for the prevention of workplace violence? Answer: Designing staff schedules to eliminate working alone. โ Distracted driving is a major concern in eliminating incidents on the roadway. Which element is the most likely to distract the driver? Answer: Use of technology โ When assuming the installation of a traffic control package, which is a significant hazard that workers face? Answer: Struck-by โ What is the main purpose of an incident investigation? Answer: Collecting facts โ Which level of hierarchy of controls replaces the hazard? Answer: Substitution โ When performing a crane lift, the MOST critical considerations include the crane load capability, stability, adjacent excavations, overhead powerlines, and which additional criterion? Answer: Slope of the surface โ In addition to determining the fuel source and the oxygen source, which other element must be identified when investigating how a fire started? Answer: The ignition source
โ How should compressed gas cylinders be stored? Answer: Upright and secured, with protective caps. โ A worker has completed training for operating a powered industrial truck. Which is the BEST testing method to assess whether the worker is operating the equipment correctly? Answer: Performance-based โ How often must hoists be inspected? Answer: A visual inspection must be made daily and a complete inspection of all ropes at least every 30 days. โ When teaching CPR, which personal protective equipment should workers be trained to use? Answer: Facemasks โ In which order are the hierarchy of controls listed from most effective to least effective? Answer: Elimination or substitution, engineering, administrative, personal protective equipment (PPE) โ Who is the person knowledgeable in the operation to be involved and competent to judge the hazards involved? Answer: Qualified person โ Which are the five primary portable power tool groups? Answer: Electrical, pneumatic, gasoline, hydraulic, and powder actuated
โ Which is the first step in dealing with alcoholism? Answer: Recognize that the problem exists โ Which position is the qualified individual whose responsibility is to detect and prevent the spread of forest during welding and cutting activities? Answer: Fire watch โ Which is the minimum clearance for cranes for 50 kV or lower power lines? Answer: 10 ft โ Which are the three main parts of a Job Hazard Analysis? Answer: Identify the job steps, hazards present in each step, and safe procedures for completing the job. โ Which habds-on method of training technique is a combination of on- the-job training classroom training? Answer: Apprenticeship โ Which entity is requires to determine if a substance meets Hazardous chemical criteria? Answer: Manufacturer โ Which does GFCI stand for? Answer: Ground Fault Circuit Interrupter โ Which entry route fot employee exposure to chemical substances is a major route? Answer: Inhalation
โ Which would be an engineering control? Answer: Installation of a sound dampener โ Which is BEST described as a sudden motion of the ground that may cause surface faulting, ground shaking, and ground failure? Answer: Earthquake โ At a MINIMUM, how often must an employer conduct an inspection of energy control procedures? Answer: Annually โ Which Anchorage-point criteria are vital for successful use? Answer: Strength and Location โ
