




Study with the several resources on Docsity
Earn points by helping other students or get them with a premium plan
Prepare for your exams
Study with the several resources on Docsity
Earn points to download
Earn points by helping other students or get them with a premium plan
SACA Exam Questions With Correct guaranteed and Assured Graded A+ Answers
Typology: Exams
1 / 8
This page cannot be seen from the preview
Don't miss anything!





SACA Exam Questions With Correct guaranteed and Assured Graded A+ Answers A Class B (flammable and combustible liquids) fire extinguisher is used to put out fires involving ALL of the following material EXCEPT? - Answer- Magnesium A company's Emergency Action Plan (EAP) should include ALL of the following except? - Answer-Machine operation procedures A hex key wrench is used to tighten which type of fastener? - Answer- Socket head cap screw After fixing a problem, what screen should be checked to verify that there are no problems before starting the machine? - Answer-Alarm An employee should be retrained if they do not perform which of these tasks after a lockout tagout is removed? - Answer-Test the machine At which two points would you measure the supply voltage? - Answer-A and C From what points or surface are baseline dimensions measured? - Answer- The front surface If a machine stops unexpectedly due to a fault, which message tells you only that the machine has a fault? - Answer-Warning message If a worker gets a chemical in an eye, what is the FIRST action he/she should take? - Answer-Go to an eyewash station
If an electronic sensor has a PNP type transistor, what effect does that have on the sensor's operations? - Answer-Output signal goes high when the sensor is triggered. In addition to a material block, what is another way a technical drawing can identify the type of material used to make the drawn object? - Answer- Local note In addition to Medical and Environmental what is another category of emergency in a company? - Answer-Hostile threats In the bolt designation shown, what is the pitch? - Answer-2. In the control frame shown, what is the information given in the block identified by the arrow labeled ITEM? - Answer-Datum reference In this drawing of a part, what type of line is identified by the arrow labeled A? - Answer-Hidden In this drawing of a two-part assembly, what is the type of fit if the shaft diameter is slightly larger than the hole diameter? - Answer-Interference In what position should a pneumatic lockout valve be placed to perform a lockout? - Answer-Closed The highlighted area in the figure shown shows which type of view of the part? - Answer-Sectional What action does pushing the manual override on a solenoid-operated pneumatic directional control valve cause? - Answer-Prevents the solenoid from operating
What indicator on an operator panel will likely be on when the machine is in normal production? - Answer-Single step What is NOT a step in an electrical Lockout/Tagout procedure?* - Answer- Write safety officer initials on tag What is the first step of the 5S process? - Answer-Sort What is the hazardous material classification system that uses pictograms to identify the danger of a material? - Answer-GHS What is the main purpose of an oil sight glass? - Answer-Determine oil reservoir level What is the measurement shown on this micrometer in millimeters? - Answer-39. What is the measurement shown on this ruler? - Answer- What is the measurement shown on this SI dial caliper, in millimeters? - Answer-22.68 mm What is the normal mode for most automated industrial machines? - Answer-What is the normal mode for most automated industrial machines? What is the pressure in the cylinder if a 1000 Newton force is applied to the rod/piston assembly as shown? - Answer-500 Pa What is the pressure shown on this gauge?* - Answer-500 kPa
What is the proper operation sequence of the fire extinguisher? - Answer- Pull, aim, squeeze, sweep What is the range by which a part dimension may vary called? - Answer- Tolerance What is the robot component shown? - Answer-Teach pendant What is the scale of the drawing if the actual length of this part is 300 mm and dimension shown by X measures 50 mm on the drawing? - Answer-1: What is the tolerance of the width of this part?* - Answer-+/-0. What is the type of robot shown here? - Answer-SCARA What is used to calibrate a precision measuring instrument?* - Answer- Gauge block What machine can be programmed to perform tasks in many different operations? - Answer-Robot What material condition does LMC define?* - Answer-Condition with the smallest amount of material What method do most small air compressors use to compress air - Answer-Piston movement What should you do if a machine safety guard has been bypassed? - Answer-Lock out the machine and call the supervisor What technology element differentiates Industry 4.0 from Industry 3.0? - Answer-Smart sensors connected to network
What type of semi solid lubricant is created by adding an additive and thickener to a liquid lubricant? - Answer-Grease What type of technical drawing shows the features of a 3-dimensional object in 2 dimensions as seen from different sides of the object? - Answer-Multiview drawing What type of wrench is shown? - Answer-Hex key What type of wrench is shown?* - Answer-Ratchet When a click-type torque wrench clicks at the set point, what do you do to apply the proper torque? - Answer-Stop turning the wrench Which of these activities is considered non-value added activity in a lean manufacturing environment?* 0/4 - Answer-Moving a product from one station to another Which of these components is used to keep the motor turned on after the start pushbutton is momentarily activated? - Answer-CR1A Which of these devices includes a display screen and software to display graphical representations of push buttons and selector switches, which an operator can press to send input signals to controllers? - Answer-HMI Which of these is NOT a primary goal of a lean manufacturing system? - Answer-Greater production volume Which of these is NOT one of the eight types of waste in Lean Manufacturing? - Answer-Underproduction Which pushbuttons must be activated to turn ON lamp 1 and turn OFF lamp 2? - Answer-A, B, and C
Which type of machine stop function requires a power-up procedure to restart the machine's operation? - Answer-Emergency stop