Download PrepIQ NASCLA Accredited Tradeination for Journeyman Electricians Ultimate Exam and more Exams Technology in PDF only on Docsity!
Tradeination for Journeyman
Electricians Ultimate Exam
Question 1. Which OSHA regulation governs fall protection requirements on commercial construction sites? A) 29 CFR Part 1910 B) 29 CFR Part 1926 Subpart M C) 29 CFR Part 1904 D) 29 CFR Part 1935 Answer: B Explanation: Subpart M of 29 CFR 1926 specifies fall protection standards for construction. Question 2. In project scheduling, a “critical path” is defined as the sequence of activities that: A) Have the longest duration but no float B) Can be delayed without affecting the finish date C) Are performed concurrently with other tasks D) Require the most resources Answer: A Explanation: The critical path has zero float; any delay extends the project’s completion date. Question 3. When reviewing a bid package, a contractor should first verify: A) The contractor’s insurance certificates B) The completeness of the drawings and specifications
Tradeination for Journeyman
Electricians Ultimate Exam
C) The subcontractor’s wage rates D) The owner’s payment schedule Answer: B Explanation: Ensuring drawings and specs are complete prevents omissions and costly change orders. Question 4. The most common method for communicating hazardous material information on a jobsite is the: A) Safety Data Sheet (SDS) B) Job Hazard Analysis (JHA) C) OSHA 300 Log D) Daily Safety Report Answer: A Explanation: SDSs detail hazards, handling, and PPE for each chemical. Question 5. Which soil classification is best suited for supporting heavy structural loads without significant settlement? A) A- 2 - 4 (Silty sand) B) A- 7 - 5 (Silty gravel) C) A-6 (Silt) D) A- 2 - 1 (Well-graded sand)
Tradeination for Journeyman
Electricians Ultimate Exam
Question 8. The correct sequence for placing reinforcement in a footing is: A) Place rebar, then pour concrete, then apply formwork B) Install formwork, set rebar with proper cover, then pour concrete C) Pour concrete, then embed rebar, then remove formwork D) Set rebar, apply waterproofing, then pour concrete Answer: B Explanation: Formwork must be in place first; rebar is positioned with required cover before concrete placement. Question 9. When installing brick masonry, the typical mortar joint thickness is: A) 1 mm B) 3 mm C) 10 mm D) 25 mm Answer: C Explanation: A 10 mm (3/8-in) joint is standard for most brick work. Question 10. Which type of steel connection is most appropriate for a moment-resisting frame joint? A) Simple bolted shear connection B) Welded full-penetration butt joint C) Pinned connection with a shear tab
Tradeination for Journeyman
Electricians Ultimate Exam
D) Riveted lap joint Answer: B Explanation: Full-penetration welds provide the rigidity needed to resist moments. Question 11. A cold-formed steel stud wall typically requires which type of fire-stop detailing at floor penetrations? A) Intumescent paint only B) Fire-resistive caulk or mineral wool pack C) No special treatment if the stud is 20 ga. D) Concrete encasement Answer: B Explanation: Mineral wool or fire-resistive caulk maintains fire-rating continuity through openings. Question 12. The most common waterproofing method for below-grade foundation walls is: A) EPDM sheet membrane B) Liquid-applied polymer coating C) Bentonite clay panel system D) Asphaltic felt Answer: C
Tradeination for Journeyman
Electricians Ultimate Exam
Question 15. The most energy-efficient glazing type for a high-rise curtain wall is: A) Single-pane clear glass B) Double-pane low-E glass with argon fill C) Triple-pane insulated glass with vacuum seal D) Laminated tempered glass Answer: B Explanation: Double-pane low-E with argon provides high thermal performance while remaining cost-effective. Question 16. A gypsum board installed on a ceiling with a ¼-in clearance from the slab is considered a: A) Suspended acoustic ceiling B) Direct-attach “drywall on deck” system C) Fire-resistive plaster ceiling D) Non-structural soffit Answer: B Explanation: When gypsum is attached directly to the structural deck with a small gap, it is a direct-attach ceiling. Question 17. Which floor covering is most appropriate for high-traffic commercial corridors? A) Vinyl composition tile (VCT)
Tradeination for Journeyman
Electricians Ultimate Exam
B) Carpet tile C) Terrazzo D) Linoleum Answer: A Explanation: VCT is durable, easy to maintain, and cost-effective for heavy traffic areas. Question 18. The required height for a toilet partition’s privacy panel in a commercial restroom is: A) 24 in. B) 30 in. C) 36 in. D) 48 in. Answer: C Explanation: A 36-in. panel provides adequate privacy per most building codes. Question 19. The placement of fire extinguishers in a commercial building must comply with which NFPA standard? A) NFPA 13 B) NFPA 14 C) NFPA 10 D) NFPA 70
Tradeination for Journeyman
Electricians Ultimate Exam
Explanation: Lead-soldered steel can leach lead; modern codes forbid its use in potable water. Question 22. The purpose of a vent stack in a plumbing system is to: A) Supply water to fixtures B) Remove sewer gases and maintain pressure balance C) Provide a drainage route for storm water D) Connect to fire sprinkler piping Answer: B Explanation: Vent stacks allow air into the drainage system, preventing siphoning and releasing gases. Question 23. In electrical conduit installation, the maximum allowable bend radius for a ½-in. EMT conduit is: A) 2 in. B) 4 in. C) 6 in. D) 8 in. Answer: B Explanation: EMT ½-in. must not be bent tighter than 4 in. radius to avoid deformation.
Tradeination for Journeyman
Electricians Ultimate Exam
Question 24. Grounding electrodes for a commercial building are required to be installed at a depth of at least: A) 12 in. B) 24 in. C) 48 in. D) 96 in. Answer: C Explanation: The NEC mandates a minimum of 48 in. (4 ft.) burial for ground rods. Question 25. The primary function of a fire sprinkler’s “dry pipe” system is to: A) Reduce water usage in the building B) Prevent water damage in unheated spaces C) Provide higher pressure flow to the heads D) Allow faster system charging Answer: B Explanation: Dry pipe systems keep the pipe filled with air, preventing freezing in cold or unheated areas. Question 26. An AIA A101 contract primarily addresses: A) General conditions and owner-contractor relationship B) Subcontractor agreements only C) Material procurement terms
Tradeination for Journeyman
Electricians Ultimate Exam
Explanation: Progress payments are staged to match work completed, supporting cash flow. Question 29. The most common method for verifying concrete compressive strength on site is: A) Slump test B) Penetration resistance test (Schmidt hammer) C) Cylinder testing at 28 days D) Ultrasonic pulse velocity Answer: C Explanation: Cured cylinders tested at 28 days provide a reliable measure of compressive strength. Question 30. In a building envelope, the term “U-value” refers to: A) The fire-rating of a wall assembly B) The rate of heat transfer through a component C) The acoustic transmission class (STC) D) The moisture vapor transmission rate Answer: B Explanation: U-value quantifies heat loss; lower values indicate better insulation.
Tradeination for Journeyman
Electricians Ultimate Exam
Question 31. A “R-value” of 30 ft²·°F·h/BTU is typical for which building component? A) Exterior wall insulation B) Roof insulation in a cold climate C) Interior partition wall D) Concrete slab Answer: B Explanation: High-performance roof insulation often targets R-30 in colder regions. Question 32. Which of the following is NOT a typical requirement for a fire-rated door assembly? A) Self-closing device B) Continuous intumescent seal C) 30-minute smoke seal rating only D) Properly rated hardware Answer: C Explanation: Fire-rated doors must have fire resistance, not just a smoke seal; a 30 - minute smoke seal alone is insufficient. Question 33. The most common cause of cracking in a concrete slab-on-grade is: A) Excessive reinforcement
Tradeination for Journeyman
Electricians Ultimate Exam
Answer: B Explanation: Fire-resistive wraps protect rebar from temperature-induced loss of strength. Question 36. In a commercial building, the minimum aisle width required for a wheelchair-accessible route is: A) 30 in. B) 36 in. C) 42 in. D) 48 in. Answer: C Explanation: The ADA requires a minimum clear width of 42 in. for accessible routes. Question 37. The primary purpose of a “safety data sheet” (SDS) on a construction site is to: A) Record daily attendance B) Provide emergency contact numbers C) Communicate hazards, handling, and PPE for chemicals D) List subcontractor qualifications Answer: C Explanation: SDSs detail chemical hazards and safe handling procedures.
Tradeination for Journeyman
Electricians Ultimate Exam
Question 38. Which of the following best describes “lead-based paint” requirements for renovation work in older commercial buildings? A) No special procedures are needed after 1978 B) Only a visual inspection is required C) An EPA-approved lead-safe work practice must be followed D) Lead paint can be sanded without containment Answer: C Explanation: EPA regulations require lead-safe work practices during renovation of buildings with pre-1978 paint. Question 39. The most common type of foundation for a low-rise commercial building on stable soil is: A) Pile foundation B) Mat (raft) foundation C) Spread footings with grade beams D) Caisson foundation Answer: C Explanation: Spread footings with grade beams are economical and suitable for stable soils. Question 40. In a building’s storm-drainage system, a “detention basin” is used to:
Tradeination for Journeyman
Electricians Ultimate Exam
Answer: B Explanation: Wet-paint fire-stop sealants must retain fire-resistance after curing. Question 43. In a commercial storefront system, the term “anchorage height” refers to: A) The vertical distance from the base to the first anchor point of the glazing panel B) The height of the storefront frame above the slab C) The maximum allowable panel size D) The distance between mullions Answer: A Explanation: Anchorage height is measured from the slab to the point where the glass is anchored. Question 44. The required minimum thickness for a concrete slab intended to support a standard office load (50 psf) is: A) 2 in. B) 4 in. C) 6 in. D) 8 in. Answer: B Explanation: A 4-in. slab typically meets the 50 psf office live load requirement.
Tradeination for Journeyman
Electricians Ultimate Exam
Question 45. Which of the following is the most common type of insulation used in interior cavity walls for thermal performance? A) Expanded polystyrene (EPS) board B) Fiberglass batts C) Spray-foam polyurethane D) Mineral wool Answer: B Explanation: Fiberglass batts are cost-effective and widely installed in cavity walls. Question 46. The “R-value” of a 2-in. thick rigid foam board with a conductivity of 0.25 BTU·in/(hr·ft²·°F) is: A) 4 B) 5 C) 8 D) 10 Answer: A Explanation: R = Thickness / k = 2 in / 0.25 = 8, but because the unit conversion yields R-value of 8 ft²·°F·h/BTU. (Correct answer: C) Question 47. In a commercial building, the required fire-resistance rating for a structural steel column supporting a 2-hour fire-rated floor is:
