Baixe CATALOGO MEDIDOR ELETROMAGNETICO e outras Manuais, Projetos, Pesquisas em PDF para Hidráulica, somente na Docsity!
Product Data Sheet
January 2014
00813-0100-4750 Rev GA
THE 8750W MAGNETIC FLOWMETER
Rosemount reliability customized for Water, Wastewater and Utility applications
Available in flanged style
PTFE and Neoprene Liners
Line sizes available from 1/2-in. (15 mm) to 48-in. (1200mm).
Options for:
- Diagnostic Suite for improved maintenance practices
- Diagnostic Suite for simplified meter verification
- Submersible to IP
- NSF Drinking Water Certification
Rosemount Magnetic Flowmeter System
8750W for Water/Wastewater & Utility Applications
Rosemount 8750W January 2014
The Rosemount 8750W Magmeter delivers reliability for
water/wastewater industries and utility applications
Operation
The operating principle of the magnetic flowmeter system is based upon Faraday’s Law of electromagnetic induction, which states that a voltage will be induced in a conductor moving through a magnetic field.
Faraday’s Law: E=kBDV
The magnitude of the induced voltage E is directly proportional to the velocity of the conductor V, conductor width D, and the strength of the magnetic field B. The figure below of a Model 8750W sensor illustrates the relationship between the physical components of the magnetic flowmeter and Faraday’s Law.
Magnetic field coils placed on opposite sides of the pipe generate a magnetic field. As the conductive process liquid moves through the field with average velocity V , electrodes sense the induced voltage. The width of the conductor is represented by the distance between electrodes. An insulating liner prevents the signal from shorting to the pipe wall.
The only variable in this application of Faraday’s Law is the velocity of the conductive liquid V because field strength is controlled constant and electrode spacing is fixed. Therefore, the output voltage E is directly proportional to liquid velocity, resulting in the inherently linear output of a Rosemount Magnetic Flowmeter.
Content
Rosemount 8750W specifications................................................................... .page 9
Dimensional drawings............................................................................. .page 15
Magnetic Flowmeter sizing........................................................................ .page 30
Material selection................................................................................. .page 33
Ordering information............................................................................. .page 34
Rosemount 8750W January 2014
Rosemount Magmeter Diagnostics reduce costs &
improve output
Rosemount Magmeters provide device diagnostics that informs the user of abnormal situations throughout the life of the meter - from Installation to Maintenance and Meter Verification.
With Rosemount Magmeter diagnostics enabled, users can change their practices to improve plant availability and output, and reduce costs through simplified installation, maintenance and troubleshooting.
Options for accessing diagnostics
Rosemount Magmeter Diagnostics can be accessed through the Local Operator Interface (LOI), a HART Field Communicator, or AMS Device Manager.
Access Diagnostics through the LOI for quicker installation, maintenance, and meter verification
Rosemount Magmeter Diagnostics are available through the LOI to make maintenance of every magmeter easier.
Access Diagnostics through AMS™^ Suite: Intelligent Device Manager for the Ultimate Value
The value of the Diagnostics increases significantly when AMS is used. AMS provides a simplified screen flow and procedures for how to respond to the Diagnostic messages.
Diagnostics Mag User Practice Field Mount Wall Mount Basic (default) Empty Pipe Process Management •^ • Electronics Temperature Maintenance •^ • Coil Fault Maintenance •^ • Transmitter Fault Maintenance •^ • Reverse Flow Process Management •^ • Advanced Diagnostic (DA1) High Process Noise Process Management •^ • Grounding/Wiring Fault Installation •^ • Advanced Diagnostic (DA2) Smart Meter Verification Meter Verification •^ • 4 - 20mA Loop Verification Maintenance •
January 2014 Rosemount 8750W
Optional Rosemount Mag Diagnostics
SMART Meter Verification
Verifying magmeter calibration has traditionally required the flowmeter to be removed from the line and re-calibrated in a flow lab or with a prover. More recently, verification using a field calibrator has become a popular solution, but it still requires extra equipment and is a time consuming process.
Now the Rosemount SMART Meter Verification diagnostic allows users to verify the flowmeter without additional equipment. Initiated directly through the meter Local Operator Interface (LOI), a HART Field Communicator or AMS™^ Suite: Intelligent Device Manager, SMART Meter Verification verifies both the transmitter and sensor calibration. The displayed results can be used to fill out the verification form, or simply print the results when using AMS Device Manager.
SMART Meter Verification delivers a fast and cost-effective approach to meter verification with no additional equipment. This diagnostic is one of the optional advanced diagnostic options (DA2) in the Rosemount 8750W Magnetic Flowmeter model number.
High process noise detection
Loop control in many chemical and slurry applications can be difficult due to “noisy” output from the flowmeter. The historic practice was to add damping to the flowmeter’s output to stabilize the flow signal. This adds deadtime to the control loop resulting in additional process variability that drives up operating costs.
Only Rosemount 8750W Magmeters have a comprehensive solution to optimize installed performance and signal stability in even the noisiest applications, without additional damping. The high process noise diagnostic alerts you when variability is caused by process noise and not actual flow variation. This allows you to adjust to a higher coil drive frequency to stabilize the output without adding damping. By taking advantage of the high process noise diagnostic and scalable coil drive capability you improve process control, increase product quality and reduce scrap. This diagnostic is one of the optional advanced diagnostic options (DA1) in the Rosemount 8750W Magnetic Flowmeter model number.
Grounding/wiring fault detection
Rosemount technology provides a grounding and wiring fault detection diagnostic to dramatically reduce the time and cost of installing magmeters. One of the most common installation issues with magmeters is the lack of a proper ground. Without a proper ground, the meter will not read flow correctly. By continually monitoring the line noise voltage across the frequency spectrum, Rosemount technology can detect and alert you immediately if the meter wiring or grounding needs to be fixed. This saves commissioning time, reduces installation costs, and can help prevent inaccurate measurements. This diagnostic is one of the optional advanced diagnostic options (DA1) in the Rosemount 8750W Magnetic Flowmeter model number.
January 2014 Rosemount 8750W
Grounding/ Wiring Diagnostic Improves Installation Practices
Diagnostic in LOI
Diagnostic in AMS
Grounding and wiring fault displays on LOI. Error messages under Diagnostic menu.^ Line noise value can be viewed.If line noise is > 5 mV, Diagnostic is tripped.
Grounding and wiring is tripped and shown in AMS status screen.
Rosemount 8750W January 2014
High Process Noise Diagnostic Improves Process Management
Diagnostic in LOI
Diagnostic in AMS
LOI indicates high process noise is detected. (^) Signal-to-noise ratio (SNR) is viewed in Diagnostic menu. If the SNR <25, Diagnostic is tripped.
Improved SNR and signal stability by moving coil drive frequency from 5 Hz to 37 Hz.
AMS status screen indicates high process noises detected and shows SNR at both coil drive frequencies.
AMS help provides procedure for adjusting mag coil drive frequency to improve signal stability.
Rosemount 8750W January 2014
Table 1. (continued) Process Temperature vs. Pressure Limits(1)
GB/T 9119 Class Flanges
Flange Material
Pressure (Mpa) Flange Rating 20 °C 100 °C 150 °C
Carbon Steel Group3E
PN10 1.00 0.92 0.
PN16 1.60 1.48 1.
PN40 4.00 3.71 3.
304 SST
Group11E
PN10 1.00 0.90 0.
PN16 1.60 1.45 1.
PN40 4.00 3.63 3.
AS2129 Table D and E Flanges
Flange Material
Pressure (psi)
Flange Rating (^) (122 °F) ^ 50 °C (212 °F)100 °C (302 °F)150 °C
Carbon Steel Group
D 101.6 101.6 101.
E 203.1 203.1 203.
(1) Liner temperature limits must also be considered.
Table 2. Process Temperature vs. Pressure Limits
JIS B
Flange Material
Pressure (Mpa)
Flange Rating (^) (122 °F) ^ 50 °C (248 °F)120 °C
Carbon Steel (^) 10K 1.4 1. 304 SST (15 to 65 mm) 10K^ 1.4^ 1. 304 SST ( ≥ 80 mm) 10K^ 1.4^ 1.
January 2014 Rosemount 8750W
Optional discrete output function
Externally powered at 5 to 24 VDC, transistor switch closure to indicate either:
Reverse flow: Activates switch closure output when reverse flow is detected. The reverse flow rate is displayed. Zero flow: Activates switch closure output when flow goes to 0 ft/s. Empty pipe: Activates switch closure output when an empty pipe condition is detected. Transmitter faults: Activates switch closure output when a transmitter fault is detected. Flow limits (2): Activates switch closure output when the transmitter measures a flow rate that meets the conditions established for this alert. There are two independent flow limit alerts that can be configured as discrete outputs. Totalizer limit: Activates switch closure output when the transmitter measures a total flow that meets the conditions established for this alert. Diagnostic status: Activates switch closure output when the transmitter detects a condition that meets the configured criteria of this output.
Optional discrete input function
Externally powered at 5 to 24 VDC, transistor switch closure to indicate either:
Net total reset: Resets the net totalizer value to zero. Positive Zero Return (PZR): Simulates zero-flow condition.
Output testing
Analog output test Transmitter may be commanded to supply a specified current between 3.5 and 23 mA. Pulse output test Transmitter may be commanded to supply a specified frequency between 1 and 10,000 Hz.
Security lockout
Security lockout switch on the electronics board can be set to deactivate all LOI and HART-based communicator functions to protect configuration variables from unwanted or accidental change.
Field Mount LOI lockout All optical switches on the display can be locked locally from the display layout configuration screen by holding the upper right optical switch for 10 seconds. The display can be reactivated holding the same switch for 10 seconds. Submergence protection (flanged sensor only) - R05/R10/R15/R20/R25/R30 Options Continuous submergence up to 30 ft. (10 m) requires conduit entries of the sensor remote junction box to be properly sealed to prevent water ingress. This requires the user to install sealed IP68 approved cable glands, conduit connections, or conduit plugs. For more details on proper installation techniques for an IP68 / submersible application, reference Rosemount Technical Document 00840-0100-4750 available on www.Rosemount.com. Option Codes R05, R10, R15, R20, R25, and R30 provide a pre-wired potted and sealed junction box to prevent the ingress of water. These options still require the use of sealed conduits to meet IP68 protection requirements. Example of a protection category: Identity letters - IP First identity number - 6 (1) Second identity number - 8 (2)
(1) Protection against the entry of dust (dust-proof). Complete contact prevention. (2) The enclosure is suitable for constant submersion in water under given conditions which are determined by the manufacturer (submersion).
January 2014 Rosemount 8750W
Electrical connections
Two 1 / 2 –14 NPT connections with number 8 screw terminals are provided in the terminal enclosure for electrical wiring.
Process reference (grounding) electrode
A process reference electrode is installed similarly to the measurement electrodes through the lining of the sensor. It will be made of the same material as the measurement electrodes.
Grounding rings - (optional)
Grounding rings are installed between the flange and the sensor face on both ends of the sensor. Single ground rings can be installed on either end of the sensor. They have an I.D. slightly larger than the sensor I.D. and an external tab to attach ground wiring. Grounding rings are available in 316L SST and Nickel Alloy 276 (UNS N10276).
Dimensions
See Figure 8, Figure 9, and Table 3.
Weight
See Table 3 and Table 5
Transmitters
Power supply
90-250 VAC rms, 50–60 Hz or 12-42 VDC
Figure 1. AC power supply requirements
Figure 2. Apparent power
DC supply current requirements Units powered by 12 VDC power supply may draw up to 1 amp of current steady state.
Figure 3. DC current requirements
DC load limitations (Analog output) Maximum loop resistance is determined by the voltage level of the external power supply, as described by:
Figure 4. Field Mount DC load limitations
Figure 5. Wall Mount DC load limitations
Supply Current (Amps)
80 100 120 140 160 180 200 220 240 Power Supply Voltage (AC rms)Power Supply Voltage (AC RMS)
80 100 120 140 160 180 200 220 240 Power Supply Voltage (AC RMS)
20
22
24
26
28
30
32
34
36
38
Apparent Power (VA)
250 Power Supply Voltage (AC rms)
Rmax = 31.25 (Vps – 10.8) Vps = Power Supply Voltage (Volts) Rmax = Maximum Loop Resistance (Ohms)
Rmax = 52.08(Vps – 10.8) Vps = Power Supply Voltage (Volts) Rmax = Maximum Loop Resistance (Ohms)
0
1
12 18 24 30 36 42 Power Supply (Volts)
Supply Current (Amps)
Power Supply (Volts)
Load (Ohms)
Operating Region
600 500
0 10.8 30
Power Supply (Volts)
Load (Ohms)
Operating Region
1000
0 10.8 (^42)
Rosemount 8750W January 2014
Note
HART Communication requires a minimum loop
resistance of 250 ohms.
Power consumption
15 watts maximum - DC
40 VA maximum - AC
Switch-on current AC: Maximum 35.7 A (< 5 ms) at 250 VAC DC: Maximum 42A (< 5 ms) at 42 VDC
Line power fuses (8712)
90–250 VAC systems 2 amp, Quick-acting Bussman AGC2 or equivalent
12–42 VDC systems 3 amp, Quick-acting Bussman AGC3 or equivalent
Field Mount
Materials of construction
Housing Low-copper aluminum Nema 4X and IEC 60529 IP Paint Polyurethane Cover gasket Buna-N
Electrical connections
Two or three 1 / 2 –14 NPT with number 8 screw terminal connections are provided for electrical wiring. CM20 adapters are available. Screw terminals provided for all connections. Power wiring connected to transmitter only. Integrally mounted transmitters are factory wired to the sensor.
Mounting
Integrally mounted transmitters do not require additional remote cables. The local display and transmitter can be rotated in 90° increments. Remote mounted transmitters require only a single conduit connection to the sensor.
Transmitter weight
Approximately 7 pounds (3.2 kg). Add 0.5 pounds (0.5 kg) for local display.
Wall Mount
Materials of construction
Housing Low-copper aluminum, NEMA 4X and IEC 60529 IP Paint Polyurethane Cover gasket Silicone Rubber Electrical connections Four 1 / 2 –14 NPT connections provided on the base of the transmitter. Screw terminals provided for all of the connections. Power wiring connected to the transmitter only. Remote mounted transmitters require only a single conduit connection to the sensor.
Note
If 3 /4 - 14 NPT connections are required, 1 /2 to 3 /4 in. adapter
kits are available for order.
Transmitter weight Transmitter approximately 9 lb (4 kg). Add 1 lb (0.5 kg) for local operator interface.
Rosemount 8750W January 2014
Figure 7. Rosemount 8750W Field Mount Transmitter
(^1) /2-14 NPT Electrical Conduit Connections* (3 places)
LOI Cover
(280)
(^1) /2-14 NPT Conduit Connections* (2 places)
(267)
(130)
(130)
(190)
1.94 (165) (49)
(224)
(78)
(76)
(87)
(148)
- Conduit connections are also available with M20 connections with the use of conduit threaded adapters.
January 2014 Rosemount 8750W
Figure 8. Rosemount Flanged Sensors, Typical of 0.5- through 4-in. (15 through 100 mm) Line Sizes
Figure 9. Rosemount Flanged Sensors, Typical of 5- through 48-in. (125 through 1200 mm) Line Sizes
(46)
A
(102)
(66)
(^1) /2-14 NPT Conduit Connection
(50.8)
(127)
(66)
H
L
A
(46)
(102)
(51)
(66)
D
(1)
(2)
L
H
(127)
2.6 (66)(1)
For 10in, 12in, 14in, 16in, 24in: (1) dimensions = 3.265 (82.8) (2) dimensions = 2.40 (61.0)
January 2014 Rosemount 8750W
Line Size (in)
Flange Rating Flange Styles
Body Height “H“
Liner Face Diameter “A”
Overall Sensor Length “L”
Flange Diameter “D”
Liner Thickness Inside Diameter Sensor Weight PTFE Neoprene PTFE Neoprene PTFE Neoprene (Lbs) 3" ASME Class 150 SO/RF 8.44 5.00 7.87 7.75 7.50 0.15 0.12 2.96 3.02 34 3" ASME Class 300 SO/RF 8.44 5.00 8.63 8.51 8.25 0.15 0.12 2.96 3.02 43 3" EN 1092-1 PN 40 SO/RF 8.44 5.43 7.87 7.75 7.87 0.15 0.12 2.96 3.02 38 3" GB/T9119 PN 40 SO/RF 8.44 5.43 7.87 7.75 7.87 0.15 0.12 2.96 3.02 38 3" JIS B2220 10K SO/RF 8.44 4.96 7.87 7.75 7.28 0.15 0.12 2.96 3.02 28 3" AS4087 PN 16 SO/RF 8.44 4.80 7.87 7.75 7.28 0.15 0.12 2.96 3.02 20 3" AS4087 PN 21 SO/RF 8.44 5.55 7.87 7.75 8.07 0.15 0.12 2.96 3.02 56 3" AS4087 PN 35 SO/RF 8.44 5.55 7.87 7.75 8.07 0.15 0.12 2.96 3.02 109 3" AS2129 Table D SO/RF 8.44 4.80 7.87 7.75 7.28 0.15 0.12 2.96 3.02 24 3" AS2129 Table E SO/RF 8.44 4.80 7.87 7.75 7.28 0.15 0.12 2.96 3.02 24 4" ASME Class 150 SO/RF 8.79 6.19 9.84 9.69 9.00 0.17 0.12 3.93 4.02 45 4" ASME Class 300 SO/RF 8.79 6.19 10.88 10.73 10.00 0.17 0.12 3.93 4.02 65 4" EN 1092-1 PN 16 SO/RF 8.79 6.22 9.84 9.69 8.66 0.15 0.12 3.93 4.02 41 4" EN 1092-1 PN 40 SO/RF 8.79 6.38 9.84 9.69 9.25 0.15 0.12 3.93 4.02 49 4" GB/T9119 PN 16 SO/RF 8.79 6.22 9.84 9.69 8.66 0.15 0.12 3.93 4.02 41 4" GB/T9119 PN 40 SO/RF 8.79 6.38 9.84 9.69 9.25 0.15 0.12 3.93 4.02 49 4" JIS B2220 10K SO/RF 8.79 5.95 9.84 9.69 8.27 0.17 0.12 3.93 4.02 35 4" AS4087 PN 16 SO/RF 8.79 6.06 9.84 9.69 8.47 0.17 0.12 3.93 4.02 28 4" AS4087 PN 21 SO/RF 8.79 6.57 9.84 9.69 9.06 0.17 0.12 3.93 4.02 68 4" AS4087 PN 35 SO/RF 8.79 6.57 9.84 9.69 9.06 0.17 0.12 3.93 4.02 119 4" AS2129 Table D SO/RF 8.79 6.06 9.84 9.69 8.46 0.17 0.12 3.93 4.02 31 4" AS2129 Table E SO/RF 8.79 6.06 9.84 9.69 8.46 0.17 0.12 3.93 4.02 33 5" ASME Class 150 SO/RF 9.64 7.31 9.79 9.71 10.00 0.17 0.13 4.95 5.04 54 5" ASME Class 300 SO/RF 9.64 7.31 10.94 10.86 11.00 0.17 0.13 4.70 4.79 89 5" EN 1092-1 PN 16 SO/RF 9.64 7.40 9.79 9.50 9.84 0.17 0.13 4.95 5.04 55 5" EN 1092-1 PN 40 SO/RF 9.64 7.40 9.79 9.71 10.63 0.17 0.13 4.95 5.04 65 5" GB/T9119 PN 16 SO/RF 9.64 7.40 9.79 9.50 9.84 0.17 0.13 4.95 5.04 55 5" GB/T9119 PN 40 SO/RF 9.64 7.40 9.79 9.71 10.63 0.17 0.13 4.95 5.04 65 5" JIS B2220 10K SO/RF 9.64 7.17 9.79 9.71 9.84 0.17 0.13 4.95 5.04 49 5" AS2129 Table D SO/RF 9.64 7.32 9.79 9.71 10.04 0.17 0.13 4.95 5.04 43 5" AS2129 Table E SO/RF 9.64 7.32 9.79 9.71 10.04 0.17 0.13 4.95 5.04 44 6" ASME Class 150 SO/RF 9.92 8.50 11.81 11.61 11.00 0.19 0.13 5.98 6.10 68 6" ASME Class 300 SO/RF 9.92 8.50 13.06 12.88 12.50 0.18 0.13 5.70 5.81 117 6" EN 1092-1 PN 16 SO/RF 9.92 8.35 11.81 11.61 11.22 0.19 0.13 5.98 6.10 67 6" EN 1092-1 PN 40 SO/RF 9.92 8.58 13.06 12.88 11.81 0.18 0.13 5.70 5.81 95 6" GB/T9119 PN 16 SO/RF 9.92 8.35 11.81 11.61 11.22 0.19 0.13 5.98 6.10 64 6" GB/T9119 PN 40 SO/RF 9.92 8.58 13.06 12.88 11.81 0.18 0.13 5.70 5.81 94 6" JIS B2220 10K SO/RF 9.92 8.35 11.81 11.61 11.02 0.19 0.13 5.98 6.10 64 6" AS4087 PN 16 SO/RF 9.92 8.31 11.81 11.61 11.02 0.19 0.13 5.98 6.10 46 6" AS4087 PN 21 SO/RF 9.92 9.13 11.81 11.61 12.01 0.19 0.13 5.98 6.10 98 6" AS4087 PN 35 SO/RF 9.92 9.13 11.81 11.61 12.01 0.19 0.13 5.98 6.10 186 6" AS2129 Table D SO/RF 9.92 8.31 11.81 11.61 11.02 0.19 0.13 5.98 6.10 52 6" AS2129 Table E SO/RF 9.92 8.15 11.81 11.61 11.02 0.19 0.13 5.98 6.10 57
Rosemount 8750W January 2014
Line Size (in)
Flange Rating Flange Styles
Body Height ”H”
Liner Face Diameter “A”
Overall Sensor Length “L”
Flange Diameter “D”
Liner Thickness Inside Diameter Sensor Weight PTFE Neoprene PTFE Neoprene PTFE Neoprene (Lbs) 8" ASME Class 150 SO/RF 10.89 10.62 13.78 13.53 13.50 0.21 0.13 7.90 8.07 105 8" ASME Class 300 SO/RF 10.89 10.62 15.60 15.42 15.00 0.18 0.13 7.62 7.72 183 8" EN 1092-1 PN 10 SO/RF 10.89 10.55 13.78 13.53 13.39 0.21 0.13 7.90 8.07 97 8" EN 1092-1 PN 16 SO/RF 10.89 10.55 13.78 13.53 13.39 0.21 0.13 7.90 8.07 96 8" EN 1092-1 PN 25 SO/RF 10.89 10.94 13.78 13.53 14.17 0.21 0.13 7.90 8.07 120 8" EN 1092-1 PN 40 SO/RF 10.89 11.22 15.60 15.42 14.76 0.18 0.13 7.62 7.72 158 8" GB/T9119 PN 10 SO/RF 10.89 10.55 13.78 13.53 13.39 0.21 0.13 7.90 8.07 96 8" GB/T9119 PN 16 SO/RF 10.89 10.55 13.78 13.53 13.39 0.21 0.13 7.90 8.07 95 8" GB/T9119 PN 40 SO/RF 10.89 11.22 15.60 15.42 14.76 0.18 0.13 7.62 7.72 154 8" JIS B2220 10K SO/RF 10.89 10.32 13.90 13.53 12.99 0.21 0.13 7.90 8.07 81 8" AS4087 PN 16 SO/RF 10.89 10.55 13.78 13.53 13.19 0.21 0.13 7.90 8.07 73 8" AS4087 PN 21 SO/RF 10.89 11.65 13.78 13.53 14.57 0.21 0.13 7.90 8.07 136 8" AS4087 PN 35 SO/RF 10.89 10.24 15.60 15.42 14.57 0.18 0.13 7.62 7.72 241 8" AS2129 Table D SO/RF 10.89 10.55 13.78 13.53 13.19 0.21 0.13 7.90 8.07 77 8" AS2129 Table E SO/RF 10.89 10.39 13.78 13.53 13.19 0.21 0.13 7.90 8.07 86 10" ASME Class 150 SO/RF 12.17 12.75 17.98 17.61 16.00 0.28 0.13 9.87 10.16 138 10" ASME Class 300 SO/RF 12.17 12.75 17.88 17.61 17.50 0.23 0.13 9.57 9.76 247 10" EN 1092-1 PN 10 SO/RF 12.17 12.60 17.98 17.61 15.55 0.28 0.13 9.87 10.16 122 10" EN 1092-1 PN 16 SO/RF 12.17 12.60 17.98 17.61 15.94 0.28 0.13 9.87 10.16 126 10" EN 1092-1 PN 25 SO/RF 12.17 13.19 17.98 17.61 16.73 0.28 0.13 9.87 10.16 158 10" EN 1092-1 PN 40 SO/RF 12.17 13.58 17.88 17.61 17.72 0.23 0.13 9.57 9.76 221 10" GB/T9119 PN 10 SO/RF 12.17 12.60 17.98 17.61 15.55 0.28 0.13 9.87 10.16 105 10" GB/T9119 PN 16 SO/RF 12.17 12.60 17.98 17.61 15.94 0.28 0.13 9.87 10.16 117 10" GB/T9119 PN 40 SO/RF 12.17 13.58 17.88 17.61 17.72 0.23 0.13 9.57 9.76 213 10" JIS B2220 10K SO/RF 12.17 12.76 17.98 17.61 15.75 0.28 0.13 9.87 10.16 118 10" AS4087 PN 16 SO/RF 12.17 12.91 17.98 17.61 15.95 0.28 0.13 9.87 10.16 168 10" AS4087 PN 21 SO/RF 12.17 13.74 17.98 17.61 16.93 0.28 0.13 9.87 10.16 258 10" AS4087 PN 35 SO/RF 12.17 12.24 17.88 17.61 16.93 0.23 0.13 9.57 9.76 333 10" AS2129 Table D SO/RF 12.17 12.91 17.98 17.61 15.94 0.28 0.13 9.87 10.16 112 10" AS2129 Table E SO/RF 12.17 12.91 17.98 17.61 15.94 0.28 0.13 9.87 10.16 127 12" ASME Class 150 SO/RF 13.17 15.00 19.91 19.58 19.00 0.26 0.22 11.88 11.96 238 12" ASME Class 300 SO/RF 13.17 15.00 19.92 19.58 20.50 0.26 0.22 11.48 11.57 346 12" EN 1092-1 PN 10 SO/RF 13.17 14.57 19.91 19.58 17.52 0.26 0.22 11.88 11.96 187 12" EN 1092-1 PN 16 SO/RF 13.17 14.88 19.91 19.58 18.11 0.26 0.22 11.88 11.96 198 12" EN 1092-1 PN 25 SO/RF 13.17 15.55 19.91 19.58 19.09 0.26 0.22 11.88 11.96 243 12" EN 1092-1 PN 40 SO/RF 13.17 16.14 19.92 19.58 20.28 0.26 0.22 11.48 11.57 340 12" GB/T9119 PN 10 SO/RF 13.17 14.57 19.91 19.58 17.52 0.26 0.22 11.88 11.96 185 12" GB/T9119 PN 16 SO/RF 13.17 14.88 19.91 19.58 18.11 0.26 0.22 11.88 11.96 204 12" GB/T9119 PN 40 SO/RF 13.17 16.14 19.92 19.58 20.28 0.26 0.22 11.48 11.57 343 12" JIS B2220 10K SO/RF 13.17 14.49 19.91 19.58 17.52 0.26 0.22 11.88 11.96 178 12" AS4087 PN 16 SO/RF 13.17 14.88 19.91 19.58 17.91 0.26 0.22 11.88 11.96 264
